The most common way for this to happen is for a metal edge to rub through the insulation on the wire. If not, check the fuses (700cc Fortwo, 451, Roadster) Still Doesn't Work! (Or The Bulb Is Dim) Check the bulb connector with a multimeter. lebikerboy is offline Quote Quick Reply post #3 of 12 (permalink) Old 03-06-2009, 08:09 AM Karl Roth Join Date: Nov 2007 Location: Hampden, MA Posts: 2,981 Thanks: 105 Thanked And that no later cars (than Mk4 ?)have this switch problem, right? navigate to this website
Yes No Sorry, something has gone wrong. Working... Really nobody have a electrical scheme..? You can only upload a photo or video. http://www.smartcarofamerica.com/forums/f70/low-beam-headlights-stopped-working-ideas-20433/
Firmly press back the lightstalk end. While the problem is most often the bulb itself, it can also be the fuse box or the switch. The rubbing compound is not quite as abrasive as the sandpaper, which means that it requires more rubbing, but the ultimate effect is the same. Today 09:16 AM by MB DNA 3 WeatherTech Custom...
Please try again later. Once removed, the sandpaper is replaced with 2,500-grit sandpaper to smooth it out, and then polished with plastic polish and a cloth. Note that passwords are case-sensitive. Note that the dipped and main may be separate bulbs, and if not are still separate filaments within the bulb (I think they are separate bulbs on all first-generation cabrios, but
MADNESS Autoworks 49,306 views 6:07 Smart 450 panel replacement part 3 - Duration: 3:26. I have once followed the advices from here and successfully cleaned and lubricated the stalk switch as described here: http://www.evilution.co.uk/pages/print.php?mod=382 Now I thought it was the same thing. The ohms of impedance reading for a good fuse should be about zero. see this here Always check to see that the headlight is working properly before driving the vehicle.
I pulled every relay out of the fusebox and still managed to turn the lights on! This is why it isn't good to rely too much on the WIS... Google search VB search Search Home Forums Community smartcarofamerica.com SITE issue Forum (not for car problems) SCoA Club Members Only New Members Area smart General Discussion smart center Dealerships smart News Watch Queue Queue __count__/__total__ Psst...!
I don't know if the headlights are on the same one as the working things you mentioned, so check anyway if you have't Check here: http://www.evilution.co.uk/index.php?id=219 http://www.evilution.co.uk/index.php?id=220 Comment Cancel Post heinkeljb http://www.fq101.co.uk/how-to-guides/fortwo-450/interior/146-light-stalk-fix.html greencarco 209,345 views 5:29 smart car Rear LED Install - Duration: 6:18. So its the switch anyway then.. Collapse X Collapse Posts Latest Activity Search Page of 2 Filter Time All Time Today Last Week Last Month Show All Discussions only Photos only Videos only Links only Polls only
OK, I will search there then, try to follow the cables from the stalk switch. useful reference By "dimmed" do you mean the parking lights (a.k.a. "side lights")? Add your answer Source Submit Cancel Report Abuse I think that this question violates the Community Guidelines Chat or rant, adult content, spam, insulting other members,show more I think that this Cheers.
A New Bulb Didn't Work Swap it over to the other side to make sure it's not another faulty bulb. Failing that, check the relays. The switch gives out power to the side lights, the interior and the rear fog light. my review here Now pull the stalk end whilst twisting further.
Once this is removed, the plastic underneath is still clear and provides a clear path for the light, increasing illumination and visibility. Install the new housing the opposite of how you removed the old one. As with many repair jobs, the hardest part is determining exactly what needs to be done.
I have one lying around, they are even classified for 220V and are S-marked! (S-mark is for the swedish electricity safety authority, Semko, which where responsible for certification of all household Remove the bulb from the connector by pulling it out straight. Video should be smaller than 600 MB/5 minutes Photo should be smaller than 5 MB Video should be smaller than 600 MB/5 minutesPhoto should be smaller than 5 MB Answer Questions with 70 miles against a concrete wall - Duration: 5:41.
selfsilent 239,513 views 5:24 Smartcar Rear Speaker Install - Duration: 13:53. Comment Cancel Post BBE Best used for spare parts Join Date: Dec 2003 Posts: 602 #6 19-11-12, 09:17 AM Re: No headlights...is there a relay or not? All fixed now. http://tekconceptllc.com/smart-car/smart-car-key-fob-not-working.php N11-3, it's brown.
Smart E.R. 7,476 views 4:50 Smart Car Front Panel Removal Change Headlamp headlight bulb light - Duration: 7:57. 365drills 235,109 views 7:57 Change headlight 2005 Smart Fortwo 450 - Duration: 8:31. So I had to resort to driving with my highbeams on tonight and last night. Really nobody have a electrical scheme..? I was assuming no relay and wanted now to add one (or two), but I need 12V out from the switch first then at least...
Skip to main contenteBayShop by categoryEnter your search keywordAll CategoriesAdvancedHi (Sign in to bid or buy) Daily Deals Gift Cards Sell Help & Contact My eBayExpand My eBay Summary Bids/Offers Watch You could try shinning a torch at the bulb and that way you my see if it's burned out by the reflection in the reflector. That is why vehicle safety inspections include checking the function of the high beams and low beams. Yesterday 10:14 PM by Johannesl 11 3 Attachment(s) Do you have the...
I don't know if the headlights are on the same one as the working things you mentioned, so check anyway if you have't Check here: http://www.evilution.co.uk/index.php?id=219 http://www.evilution.co.uk/index.php?id=220 Fuse 5-8 are all I misread some information from smart. Most of the time, they are held in place by hex-head screws that require a 10mm socket to remove. The side lights work, but the high beams or head lights do not, I am able to flash the high beams but they do not stay on.